A private Bafang BBS DIY conversion does not require vehicle approval merely because the electric drive was retrofitted. What matters is the actual technical characteristics of the completed bicycle.
This is the point addressed by the GutRad StVO Module. It does not grant official approval for an individually converted bicycle or take over the converter’s responsibility for the complete vehicle. For compatible Bafang BBS UART systems, it establishes a defined, documentable operating state and checks the relevant controller data at each startup.
When does an electrically assisted bicycle legally remain a bicycle?
Section 1(3) of the German Road Traffic Act (StVG) refers to the actual properties of the auxiliary electric drive. Key criteria include:
- rated continuous power of no more than 250 W;
- assistance that decreases progressively as speed increases;
- motor assistance ending no later than 25 km/h;
- motor assistance ending when the rider stops pedalling.
Starting or walk assistance up to 6 km/h may also be fitted. A motor label, 250 W sticker or number entered into software therefore does not by itself determine classification. The actual behaviour of the completed bicycle matters.
A private conversion can also qualify as a pedelec
Bicycles can in principle be converted into pedelecs. Retrofitting a motor does not automatically turn a privately converted bicycle into a motor vehicle requiring approval. At the same time, the finished bicycle must satisfy the applicable technical requirements. Entering 25 km/h and 250 W in a controller does not automatically make every DIY conversion compliant.
The converter remains responsible
Anyone converting their own bicycle remains responsible for its technically sound condition. This includes more than the motor and controller: proper installation, frame, brakes, wheels, electrical equipment and other safety-relevant components are also the converter’s responsibility.
GutRad does not take over this responsibility or issue government vehicle approval. Private converters decide whether and how they wish to document their drive system’s technical characteristics. GutRad offers a technical solution and documents the operating state it establishes and monitors for that system — no more and no less.
Why personal controller programming is a different concept
Bafang BBS UART systems are generally programmable. Power, speed and other controller parameters can be changed with suitable tools. A user-defined setting may initially establish a particular state, but the converter must then consider how that state can be demonstrated and how subsequent parameter changes are handled.
A screenshot of programming software or an additional 250 W sticker is not the same as technical monitoring of the configuration actually stored in the controller.
What does the GutRad StVO Module do?
The module goes beyond a one-time programming operation. A defined GutRad parameter set is established for the intended pedelec operation on a compatible Bafang BBS UART system. Each time the drive starts, the relevant controller data are checked again. If they differ from the prescribed set, the module overwrites the affected values using the saved GutRad configuration. Changes to monitored parameters therefore do not simply remain in effect permanently.
Why save the original controller data?
The controller settings present before the first adjustment are backed up. There is a practical reason: the module is sold as a shipped product. If, for example, a customer exercises their right of withdrawal and does not wish to keep it, the controller should be capable of being returned to its pre-installation condition.
The GutRad Key is not a tuning switch
The GutRad Key is not required for normal intended pedelec operation. Its main purpose is removal and restoration: it can restore the controller data saved before the module was installed. It is not intended to switch between pedelec mode and unrestricted operation.
If the original controller state is restored and the StVO Module removed, GutRad makes no statement about the subsequently used controller configuration or the bicycle’s legal classification.
Permanent use: the backup can also be replaced with the GutRad set
If the converter decides to use the StVO Module permanently, the originally saved controller data can be overwritten with the GutRad StVO set. The backup then contains only the configuration intended for pedelec operation. The pre-installation data can no longer be recovered from that backup.
DIN EN 15194 and protection against changes
DIN EN 15194 is an important technical standard for electrically power-assisted cycles. The German edition cited in the original article is DIN EN 15194:2024-03. Alongside power and assistance cut-off characteristics, the standard addresses measures intended to prevent changes to relevant drive parameters.
For freely programmable retrofit drives, the question is therefore not only which values were configured once but what happens after those values are changed. The GutRad approach checks relevant controller data at every startup and overwrites detected deviations with the stored set.
GutRad does not thereby claim that an individually converted bicycle has DIN certification. The requirements for the complete vehicle remain the converter’s responsibility.
What GutRad documentation means — and what it does not
GutRad documentation does not itself create an exemption from vehicle approval. Classification follows from the vehicle’s actual technical characteristics. The documentation explains the condition established and monitored by the StVO Module for a compatible drive. Private converters may decide whether to use this additional evidence; responsibility for the complete bicycle remains theirs.
In practical use since 2019
GutRad has offered the StVO Module since 2019. Based on the feedback and experience available to GutRad, we are not aware of a case since the sales launch in which a qualified inspector or expert objected specifically to the functionality of a properly used module. This is neither official approval, a court ruling nor a legal guarantee. We nevertheless consider it relevant that the system has been used in practice for several years.
Our position
A private Bafang BBS conversion is not automatically illegal. Equally, fitting a powerful Bafang BBS with a 250 W sticker or changing a software value does not automatically make it a compliant pedelec. The actual properties of the drive and completed bicycle are decisive.
GutRad provides a defined, repeatedly verified and documentable operating state for its part of the system — no more and no less. What matters is not what is printed on the motor, but what the system actually does.
Further information
- Section 1 StVG — official German legislation
- German Bundestag Research Services — Legal Regulation of Pedelecs
- GutRad StVO Module — Technical Overview
- GutRad StVO Module, Version 2.0
General technical and legal information, not individual legal advice or a technical assessment of a specific vehicle.








